Acti ENR-1000 User Manual download pdf (Page 98)

www.acti.com

ENR-1000 Series System Administrator’s Manual

Please note that any change you make on this page requires the system to restart its service,

please wait for a while and reconnect ENR using the new properties.

Enable DHCP Server

You may enable the built-in DHCP server for either LAN1 (default) or LAN2 port.

Go to Setup page  Network tab click “DHCP Server”.

1. Check “Enable” and select a LAN, this LAN has to be in Manual mode.

2. Set the Beginning IP Address and Ending Address, and click “Save”. ENR will assign

IP addresses within this range to the cameras connected to the selected LAN port.

Please (1) make sure the cameras are in DHCP client mode, (2) connect and power the

cameras up after you enable this service.

Field Name

Description

HTTP Port

The connection port is used for remote web client to communicate with

ENR. Default is 80.

Default Gateway

Default uses LAN2’s setting.

Connection Type

Choose one connection type for this LAN port. DHCP and PPPoE service

will assign an IP Address to ENR, and there is no need for you to define

other network information.

Manual: Please obtain a static IP address and other network information

including Subnet Mask, Gateway and DNS server from your network

administrator.

DHCP: Use this connection type if you have a DHCP server on your

network router.

PPPoE: Chose this when your ISP is using PPPoE type DSL line. Please

contact you ISP to get the Username and Password for this connection.

LAN1 default is Manual; LAN2 default is DHCP.

IP Address

Fixed IP Address. LAN1 default is 192.168.0.10; LAN2 default is Auto.

Subnet Mask

Used to define if the destination is in the same subnet. LAN1 default is

255.255.255.0; LAN2 default is Auto.

Gateway

A valid gateway setting is essential for data transmission between

different subnets, such as accessing the DNS service or SMTP server

on the Internet. LAN1 default is 192.168.0.254; LAN2 default is Auto.

DNS Setting

The DNS server that translates domain names to actual IP addresses. If

this LAN is Manual mode, and you will set an SMTP server for event

notification, be sure to set the Primary DNS and Secondary DNS. LAN1

default is Manual; LAN2 default is Auto.

1 2 ... 93 94 95 96 97 98 99 100 101 102 103 ... 142 143

ENR-1000 Series 1
Legal Notice 2
3 3
About This Manual 4
Table of Contents 5
6 Installation 20 6
7 7
8 8
9 9
10 10
Introduction 11
12 12
13 13
14 14
Supported Video Format 15
Get Started 16
At A Glance 17
18 18
LED Indicators 19
Installation 20
21 21
Install the Hard Disks 22
23 23
24 24
25 25
Connect the Devices 26
Quick Setup 27
28 28
29 29
Local Client Operation 31
Input Devices 33
34 34
36 36
37 37
38 38
39 39
40 40
41 41
42 42
Change Camera Settings 43
44 44
45 45
46 46
47 47
Open PTZ Panel 48
Device Information 51
Network Settings 52
53 53
54 54
55 55
56 56
Date & Time 57
E-mail Settings 58
59 59
61 61
62 62
63 63
Schedule Recordings 64
65 65
66 66
68 68
69 69
70 70
71 71
72 72
73 73
76 76
78 78
79 79
82 82
1 2 3 83
4 5 6 83
7 8 9 83
85 85
Customize System Language 86
87 87
Remote Client Operation 88
89 89
90 90
Log In / Out 91
92 92
Setup Wizard 93
Setup the System 94
95 95
96 96
97 97
98 98
99 99
100 100
101 101
102 102
Live Page UI Overview 103
104 104
Set Cameras 105
106 106
107 107
108 108
109 109
110 110
111 111
112 112
113 113
114 114
115 115
116 116
117 117
118 118
119 119
120 120
Set Recording Schedule 121
122 122
123 123
Event Management 124
125 125
126 126
127 127
128 128
129 129
130 130
Disk Management 131
132 132
Upgrade Firmware 133
Backup / Restore Settings 134
135 135
User Group Management 136
137 137
138 138
Joystick 139
System Log 140
141 141
Customize Live Screen Layout 142
143 143

Comments to this Manuals

No comments

Acti ENR-1000 User Manual Page 98

Comments to this Manuals

Related products and manuals for Camcorders Acti ENR-1000