ACTi E37 Manual Page 1

Bullet Camera Series Hardware Manual E37 Ver. 2014/03/20

www.acti.com Hardware Manual 10 Installation Procedures Using the Bundled Bracket Step 1: Install the Bundled Bracket 1. Mark the

www.acti.com Hardware Manual 11 Step 2: Attach the Sunshield The use of sunshield is optional if the camera will be installed indoo

www.acti.com Hardware Manual 12 Step 3: Install the Camera 1. Depending on how you want to install the camera, attach the camera t

www.acti.com Hardware Manual 13 Step 4: Waterproof and Connect the Cable The camera and the pre-installed network cable, “pigtail”,

www.acti.com Hardware Manual 14 How to Use the Cable Gland This section describes how to waterproof the cable-out or “pigtail” of t

www.acti.com Hardware Manual 15 2. Insert the clamping nut into the Ethernet cable. 3. Insert the sealing insert with claw.

www.acti.com Hardware Manual 16 6. Connect the Ethernet cable connector to the “pigtail” connector. 7. Attach the gland body to

www.acti.com Hardware Manual 17 How to Use the Conduit Gland This section describes how to waterproof the cable-out or “pigtail” of

www.acti.com Hardware Manual 18 2. Pull the Ethernet cable through the flex conduit. Leave enough length of the cable outside the

www.acti.com Hardware Manual 19 6. On the “pigtail” side, insert the washer into the “pigtail”. 7. Connect the Ethernet cabl

www.acti.com Hardware Manual 2 Table of Contents Precautions 3 Safety Instructions ...

www.acti.com Hardware Manual 20 9. Push the flex conduit and insert the sealing nut into the gland body. NOTE: Make sure the

www.acti.com Hardware Manual 21 Step 5: Connect the Cable Connect the other end of the network cable to a switch or injector. Then,

www.acti.com Hardware Manual 22 Other Adjustments and Accessories This section describes the procedures on installing a memory card

www.acti.com Hardware Manual 23 3. When done, ensure the rubber seal is aligned and attached to the back cover and then close the

www.acti.com Hardware Manual 24 How to Reset the Camera In case there is a need to reset the camera to its default factory settings

www.acti.com Hardware Manual 25 Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera

www.acti.com Hardware Manual 26 By double-clicking with the left mouse on the camera model, it is possible to automatically

www.acti.com Hardware Manual 27 Using the Default Camera IP Address If there is no DHCP server in the given network, the user may h

www.acti.com Hardware Manual 28 Manually adjust the IP addresses of multiple cameras: If there are more than one camera to be used

www.acti.com Hardware Manual 29 Access the Camera Now that the camera and the PC are both having their unique IP addresses and are

www.acti.com Hardware Manual 3 Precautions Read these instructions You should read all the safety and operating instructions before

www.acti.com Hardware Manual 30 The following examples in this manual are based on Internet Explorer browser in order to cover all

www.acti.com Hardware Manual 4 Federal Communications Commission Statement This equipment has been tested and found to comply with

www.acti.com Hardware Manual 5 Safety Instructions Don’t open the housing of the product Cleaning Disconnect this video product fr

www.acti.com Hardware Manual 6 Introduction List of Models This hardware manual contains the following models: E37 10MP Bullet wit

www.acti.com Hardware Manual 7 Package Contents Camera Conduit Gland Cable Gland Washer (x2) Sunshield Sunshield Screw Kit Br

www.acti.com Hardware Manual 8 Physical Description 1) Memory Card Slot Insert a memory card (not included) into this slot for l

www.acti.com Hardware Manual 9 Mounting Options In areas with fierce weather conditions, the light bundled bracket can be replaced